Handi Rifles - a few Questions

[R Cubed]

Greetings - I am new to NEF Handi Rifles and this Forum. I picked up a gently used one from my favorite store on Firday with a Simmons 3-9x32 scope on Weaver rings. It is chambered for .30/06.  I sent a letter off to NEF requesting an Owners Manual. Untill I receive it will you enlightend me as to a few of the finer points of these rifles? Can it be dry fired?  The serial number begins NJ32xxx. Can I find out when it was manufactured? This riflles looks like it will be fun to shoot and plink with - I reload and would like to know what you folks reload for a .30/06.

I look forward to spending time on the forums here...

Thanks,

[Critter]

Well don't I feel like an idiot.
Learn something new everyday.

Don't beat yourself up, the FAQ was a little vague on that detail, I added a line that will help.

Thx,

Tim

[quickdtoo]

Welcome to GBO!! Critter's post has incorrect info, the first letter N signifiies NEF, H would be H&R, the second letter denotes year of mfr, J = 1995, anything older than N or 1999, can't be fitted with any high pressure barrels if you ever decide on that route. Don't be frustrated that they won't fit other high pressure barrels to a frame that already has a high pressure barrel on it, that's just the way they run their show.

Tim

[bearfat]

My avitar on left shows a 30-06  with the Choate stock (pro's and con's with the stock) that used a Sierra 220 gr RN to drop the donut blob showing. I have loaded Nosler 200 gr Partition also for the NEF and dropped one deer with it. I was able to load up to max loads per Sierra and Noslers manuals without any problems although the Sierra 220 gr have a good kick to them.

For heavy hunting loads I was a staunch believer in the Nosler 200 gr in all my 30-06's until the last few years (sorry Nosler). I switched to Sierra. Jury still out on Sierra until I harvest another half dozen game animals.

Still looking for the right scope. Will be using an Aimpoint this fall?

So I say load up to max in proper steps looking for signs of pressure if you like the heavy bullets like me.

I did try a half dozen various 150gr .30 cal factory and reloads I had lying about hoping to find one the NEF really liked but no go.


                                         NEF in 30-06 cal with Choate stock

So the Sierra 220 gr loaded to max using IMR4350 powder per whatever the Sierra manual says is fine for me now.
I'm not an expert on firing pins and I do dry fire but only rarely. I don't think it's good for them. 

[R Cubed]

Is there website where I can download an Owners Manual?

[Coastwatcher]

The manual I have says that they should not be dry fired.   I will scan it and e.mail it to you.   Its only a single 8-1/2 by 14 sheet, both sides.

[R Cubed]

Posted by: Coastwatcher 
Insert Quote
The manual I have says that they should not be dry fired.   I will scan it and e.mail it to you.   Its only a single 8-1/2 by 14 sheet, both sides.


That would be kind of you - Thank you very much.

Rick

[Coastwatcher]

On its way.  Good Luck.

[Brett]

As a general rule I do not dry fire any firearm I always use 'snap caps' or a spent shell at the very least. 

[R Cubed]

Coastwatcher - Email received and converted to Word document for printing. Thank you! Rick

[myarmor]

Dry firing can lead to a broken transfer bar...bad news.
Buy a snap cap or make your own using a once fired brass and pop the spent primer out and put a rubber eraser trimmed in it's place...wish I could claim this idea, as it's a very good one, but I found it on the net...I believe on the reloaders bench.
Anyway a cheap alternative, and very usefull too.
-Aaron

[cwlongshot]

Dry firing can lead to a broken transfer bar...bad news.
Buy a snap cap or make your own using a once fired brass and pop the spent primer out and put a rubber eraser trimmed in it's place...wish I could claim this idea, as it's a very good one, but I found it on the net...I believe on the re-loaders bench.
Anyway a cheap alternative, and very useful too.
-Aaron

 Aaron,
 Want cheap snap caps? Try what I do, take a case for the caliber you need a cap for. re-size it and DRILL the primer pocket with a 1/4" drill bit. Now TAP it 1/4-20, its brass, it will be EASY!! Now go to the hardware/Home Depot/Lowes/ Tru-value what ever and buy a couple 1/4-20 NYLON screws. Screw it in the case and cut off with a razor, flush with the case head. WALLA!! You just made a snap cap!!  Cheap and easy!!

 I make one for every Handi I own!! Good rainy day project.

 CW

[dw06]

cw,thats a great tip thanks for posting it!

[myarmor]

That is another interesting way to make a snap cap I never thought of. I always appreciate info like this.
Thanks.

[R Cubed]

I like the snap cap suggestion - Cool Beans!