|Topic Review (Newest First)|
|06-20-2019 01:16 PM|
Originally Posted by carbineone1964 View Post
|06-19-2019 10:34 AM|
|carbineone1964||Thanks for sharing the videos. Looks like you are working everything out and having some fun also.|
|06-17-2019 10:27 PM|
Looks like you're getting it nailed down.
I was guesstimating about 220, looks like I wasn't too far off. That tight fitting fat slug means a lot of pressure and recoil generated. Way than with a round ball with the same charge.
My Napoleon is a little smaller and lighter overall, but isn't that violent with 250. Of course it's pushing a 1.125" round ball that weighs a little over a third of your slug, with .031 windage. I'm sure if I double-balled it, it would get testy.
That looks more like it behaved before I backed off from 280 in the beginning (I only fired a few of those). I didn't want it beating the carriage apart, and now that the new has long since worn off and it's getting on in years I'm probably back it down even more.
Truth be told I could probably fit all the balls it's ever fired at a target in both hands. The vast majority of it's work has been entertainment, salutes on holidays (or just whenever) with the neighbors and there kids cheering it on, and it's not going to retire from that anytime soon I hope.
|06-17-2019 11:23 AM|
Okay, I finally got a day of clear weather to test out the different charges.
I put together prepared charges of 150, 200, 250, and 300 grains of Goex Cannon powder. I was shooting at a target 50 yards away.
150gr Shot 1 - couldn't locate where shot landed
150gr Shot 2 - round keyholed in target board on lower right
200gr - round punch through board above targets right shoulder (left side) and either it wasn't tumbling that badly or it just happen to hit at the right point in the spin, since the hole seem a bit ragged, but otherwise round.
250gr - I mislaid the gun, so the round hit way right, but my spotter (a friendly shooter who happened to be on the range at the time) said it seemed pretty straight. The gun still jumps. so this is probably too big a of a charge already.
300gr - Way too big a charge. Gun jumped and the round overshot the 50yard berm and impacted about 10 feet up on the 150yard berm (trees and a large hill past that, so we were safe even if it went over that one).
So, in summary, it looks like the 200 grain charges are the gun's sweet spot.
|05-20-2019 02:06 PM|
|double d||Hack saw and angle grinder.|
|05-20-2019 09:57 AM|
|beowulf_grendel||Speaking of zinc, and maybe I should start a new thread, but how do you handle the sprue when casting zinc? I know the temps are in line with lead (a bit higher), but zinc is significantly harder. Can you use the same sprue cutting mold types as with lead, or do you need to leave it open topped and then grind the sprue down?|
|05-20-2019 09:55 AM|
Thanks, Double D, for all the info. When I can get a nice (non-pouring rain) free Saturday, I'll take the gun out to the range and see if I can work the charges up and find one that it seems to like. I wish I had the ability to shoot it out back, but my HOA (and the retirement home immediately behind me) would probably frown on that. Oh well, such is the problem with city life.
I do have some wheel weight lead now (plus about 350 lbs of soft lead from a retired NSSA shooter who got out of the game), so I'll see if I can get a nice clear evening and cast some new slugs out of the wheel weight lead (and maybe melt and recast the existing slugs at a higher temp to see if I can get rid of the wrinkles). It's been pouring out here, so chances have been limited.
|05-19-2019 11:53 AM|
|carbineone1964||I also would like to get some Zinc rounds made for my 40mm. I have so far failed with my Zinc Casting deficiencies. I am going to try again soon since the weather is decent outside now. I just so far have not been able to cast good Zinc rounds. It just seems much more difficult for me than lead.|
|05-19-2019 11:12 AM|
|Terry C.||I was going to suggest zinc, but I read back and saw the mold is aluminum. That would drop the weight from 14 oz. to less than 9.|
|05-19-2019 08:28 AM|
|double d||Sounds like you are are safe grounds there Bruce. Breech loaders are a different animal than muzzleloaders, still you need to be cautious, and so you are.|
|This thread has more than 10 replies. Click here to review the whole thread.|