Graybeard Outdoors banner

1 - 10 of 10 Posts

·
Registered
Joined
·
10,335 Posts
Discussion Starter #1
I bought a set of these. One in each barrel length. Sold the 7&1/2” one. Don’t like long revolver barrels. Kept the 4 &5/8 and the 5 & 1/2” . Actually believe I like the 5&1/2”’ best. Shoots real good and carries good too in a El Paso saddlery tanker shoulder holster.
 

·
Premium Member
Joined
·
4,548 Posts
I just went through the process of have Alan Siegrist rebore and rifle a K22 barrel then sending my S&W model 15 the barrel and a K22 cylinder to Andy Horvath everything to build me a K32 in .327 Federal.
Steve
 

Attachments

·
Premium Member
Joined
·
16,456 Posts
I was going to post up who has and what do they think...

But nearly six months and one reply kinda tells the tale.


I have been watching these for a few months. Im going to order a Single Seven tomorrow.

Im debating between the stainless standard model and the Bisley Blued. My heart is with the Bisley. Thats probably what I will order.

I just ordered 200 Starline cases and proved my dies for the H&R are long/deep enough.

I also borrowed a 140g HP mold. And have a few hundred cast and Powder coated. I know this has limited cyl length so Time will tell
If these bullets will work. But no worries as I will never sell My Trotter 32/20 and its throat is plenty deep for these!!

FAED8A51-7F08-4E98-9375-EF67B6C82629_1578010589568.jpeg

6B260E25-4F0A-4505-A0FF-60B9139EEFBE_1578010617601.jpeg

CW
 

·
Premium Member
Joined
·
16,456 Posts
D42A2289-8D22-4ED1-A80B-0A9E76C572A3_1578490286814.jpeg

Licked it up Last night. Kinda rough... Ruger built it quickly. ;(. I disassembled the ejector cause the very first use had it stuck extended thru the cylinder. ;(
Fixed that pretty easily. Stoned the burrs away filled off the flashing on the rod itself and then ten minute application of JB bore paste. Followed with brake cleaner hose-out and greased/lubed lightly. Working slick as can be now.

I spent a hour or so making Dummies and setting up dies with five differ et cast bullets. I wish I had bought more 115 g Speers but at least 100g XTPs are still attainable. Out of my five cast three will work as is. One will work if I trim case back. (Not gonna fudge with that. Ill just shoot in my trotter 32/20) One Im excited about is the Lyman 311440 150g. Its gonna be a PILEDRIVER!!

49CAEDED-1EE7-4269-84BE-F6741DC817FA_1578490602816.jpeg

I need to creat the data. Gonna start with 2400 and Unique. The bullet fits the short cylinder like a GLOVE!

Anyone tried heavies in the 327?

CW
 

·
Registered
Joined
·
600 Posts
Since I've never had the chance to see one of those, is the cylinder the same outer diameter as a .22 Single Six?
 

·
Premium Member
Joined
·
16,456 Posts
I havent measured diameter, but appears to be yes. But it is a bit longer.

CW
 

·
Premium Member
Joined
·
16,456 Posts
649F5EC8-0B07-4B15-9D32-83C82347D574_1578652853368.jpeg 2D8B45FD-877E-40D3-A3DC-422DA87D4CBB_1578652821449.jpg

These are all RF Rugers.

CW
 

·
Premium Member
Joined
·
16,456 Posts
18E4090B-7D46-44D4-BE70-F94087947B7B_1578831881913.jpeg

Ready for first shots later today.

CW
 

·
Registered
Joined
·
10,335 Posts
Discussion Starter #9
Those are nice looking reloads. That WFP should be a real thumper. I like the Bisley grip but have come to prefer the stainless guns.
 

·
Premium Member
Joined
·
16,456 Posts
I would have LOVED a sts Bisley in 327!!!!

49A14769-C0BA-49DC-86EB-2E324DB25DFB_1578960377686.jpeg 6C1CB524-9305-48B5-A6B8-B9D640731F54_1578960363678.jpeg

LtoR 150G (Lyman 311440) 135G (Accurate 31-137) Factory Speer 115 GD

CW
 
1 - 10 of 10 Posts
Top